Metabo PS 18000SN Stainless Steel Submersible Dirty Water Pump with Float Switch 11 Metre Lift 18000 Litre Hour Max Flow 1100w 240v

Our Price
£229.95 inc VAT
 

QL166213

  • Our Part Number M0251800000
  Email this page Printable version

Details

Metabo PS 18000SN Stainless Steel Submersible Dirty Water Pump with Float Switch 11 Metre Lift 18000 Litre Hour Max Flow 1100w 240v

Whether tasked with clear or dirty water this pump has what it takes to get the job done, no messing! Even when visibility is next to nothing, it performs strongly thanks to first-class technology. Depending on the model, it extracts particle sizes up to 35 mm. Submersible down to a depth of seven metres and with a delivery height of up to eleven metres, it can handle conditions which many other pumps can not even touch.

Features:
- Perfect for pumping out, pumping dry and recirculating fresh or dirty water from containers, tanks, swimming pools or flooded cellars
- Suitable for watering gardens and lawns from water reservoirs
- Float switch for automatic mode
- Level regulation of the float switch
- Housing made of non-corrosive stainless steel
- For coarse grime of a particle size of up to 35 mm
- Ergonomic carry handle

Includes:
Angle connection piece with multi-adapter
Float switch

Specifications:
Power - 1100 Watts
Max. Delivery rate - 18000 l/h
Max. Delivery height - 11 m
Max. Submersible depth - 7 m
Max. Pressure - 1.1 bar
Flat suction up to - n/a
Max. particle size - 35 mm
Discharge Port - 1 ½'' female thread
Pump housing - Tough plastic
Power Cable - 10 m
Weight - 7.8 kg

Additional information regarding Submersible Water Pumps
Clean Water Pumps:
Generally clean water pumps are suitable for the drainage of cellars, sinks, cisterns, pools, baths and other general transfer of water. They are not suitable for outside ponds or other dirty water as they will only usually allow small particles to pass through. Most clean water pumps will allow suction to a very low level (normally within 5 - 10mm) before they cut out but remember this only applies if they have a float switch.

Dirty Water Pumps:
These are suitable for the drainage of most water types as they allow for a much larger particle types. Be aware however that they will usually drain water down to a level of between 25 - 50mm depending on the particle size that they allow for. Automatic cut out only applies if they have a float switch. Unless specified dirty water pumps are not suitable for agriculture type use or for drainage of water containing salt or other chemicals. The term 'dirty' in most cases applies to 'water contains small particles such as grit, sand, mud and small pebbles'.

Considerations when buying a Submersible or Surface water pump:

1. Particles over 1mm generally, can only pass through dirty water pumps. Always buy a pump that will allow the particle size that you require to flow through it.

2. Float switches enable the pump to cut-out when the water reaches the minimum level at which the pump can operate without overheating. Clean water pumps can operate at a lower level than dirty water pumps as they do not have to account for particles being able to pass through the bottom of the pump. Pumps without a float or auto cut out type switch cannot run automatically and have to manually be controlled.

3. Water pumps have differing flow rates so ensure you purchase a pump capable of transferring water at your desired speed; this is normally calculated as litres per second or litres per hour.

4. The distance or height that a water pump is capable of moving water is known as the lift height use the following calculation to determine if the pump is suitable for your requirements:

The maximum flow rate of a pump is directly affected by the height it has to lift the water. In general the flow rate will decrease as the lift height increases. Horizontal pumping distance is also affected use the formula Max Height - Working Height x 10 to determine the maximum horizontal distance the pump will be capable of.

It is recommended that an RCD is always used with a submersible pump as should be the case whenever electrical products are used near water.

Important:
Most submersible pumps require a lay flay hose (except water butt pumps) which have a wider diameter than garden hose in order to drain the water without damaging the pump, to allow for particles (if applicable) and to allow for fast flow rates.

Specifications

Mfr Part NumberPS 18000SN
Our Part NumberM0251800000
Power240v Electric
Shipping Weight7.8kg
ManufacturerMetabo
Cable Length (m)10m
Float SwitchYes
Flow Rate300 l/min
Lift Height11m
Model NoPS 18000SN
Output Aperture (mm)38mm
Wattage1100w
Item Weight7.8kg
Clean or Dirty WaterDirty

Reviews

Sort by

Showing 1 to 0 of 0 reviews

Most Recent Customer Reviews for Metabo PS 18000SN Stainless Steel Submersible Dirty Water Pump with Float Switch 11 Metre Lift 18000 Litre Hour Max Flow 1100w 240v

This product is yet to be reviewed. Be the first to leave a review.


Videos & Downloads

Available videos for this product

Metabo Corporate Video

Metabo Quality Control Video

Available downloads for this product

Get Adobe ReaderYou may need Adobe Reader to view some of our downloads. If you do not already have it installed please click the icon to the left to install it

More Help

More Help with this product...

If you require more information or assistance with this product please consult the links below :

Bulk Prices

Do you have a bulk order?

If you have a bulk order for this item then we may be able to offer you an extra discount. Please call our order line on 0844 335 3902 for a quote.

Please note : to qualify for a bulk discount where not already specified on the website, a bulk order would be considered to be normally a minimum of around 100 units for lower value items, and sometimes less if it is high value item.

 

Tooled-Up.com