Trend Trimming Cutter Bits

Trend Trimming Cutter Bits at Tooled-Up.com

Trend Trimming Cutter Bits are bearing guided router cutters designed to follow an existing edge and trim laminate, veneer, timber or board flush, or to a set profile, with a clean finish. Tooled-Up.com stocks them in several formats, including straight trimmers, bevel trimmers, overlap trimmers, double trim cutters and combination trimmers.

The selection covers both standard Trend cutters and the CRAFTPRO series, which includes 3 flute, bevel, overlap, double bearing and pierce and trim versions. There are also specialist options such as the Trend Bearing Guided Trimmer Router Cutter for Veneer and the Caravan Ind Guided Pierce and Trim Double Two Flute Router Cutter.

Because the bearing rides along the workpiece edge, each cutter gives repeatable results without a fence or template. That makes them a practical choice for fitters, joiners and workshop users who need consistent edges.

Key Features of Trend Trimming Cutter Bits

• Bearing guidance: The bearing follows the board edge, so the cut stays accurate along the full length of the workpiece.
• Double trim action: The Trend Bearing Guided Double Trim Router Cutter trims the top and bottom surfaces in a single pass, saving time on laminated and veneered boards.
• Bevel trimming: The bevel trimmer cuts a wider edge line at an angle of 80 degrees, giving a neat chamfered finish to laminate edges.
• Bearing options: A 16mm bearing is supplied as standard on the bevel trimmer. A larger 19mm bearing spreads wear across the cutting edges, which helps extend working life.
• Overlap trimming: Overlap trimmers deal with surfaces that overhang the substrate, leaving a flush edge.
• Multiple flutes: The CRAFTPRO 3 flute cutter and two flute pierce and trim designs suit different finish and feed rate needs.
• Combi trimmers: A combination cutter lets you handle more than one trimming task without changing bits as often.

Who Uses Trend Trimming Cutter Bits?

Kitchen fitters use them to trim worktop laminate and edging flush. Joiners and cabinet makers rely on them for veneered boards, panels and shopfitting work. Caravan and motorhome builders use the pierce and trim cutters for cutting out and finishing panels. Furniture makers and serious DIY users also find them useful for tidying edges on laminated projects.

Popular Trend Trimming Cutter Bits

Bearing Guided Trimmers

The standard Trend Bearing Guided Trimmer Router Cutter and CRAFTPRO equivalent suit general flush trimming. A veneer-specific version is also available.

Bevel and Overlap Trimmers

These suit angled laminate edges and overhanging surfaces. Look for the Trend Bearing Guided Bevel Trimmer and Overlap Trimmer, plus their CRAFTPRO versions.

Double Trim and Pierce and Trim Cutters

Choose the Double Trim, CRAFTPRO Double Bearing Guided Trimmer or pierce and trim cutters for faster work on panels. Shop Trend Trimming Cutter Bits to compare each type.

Combi Trimmers

The Trend Combi Trimmer Bearing Guided Router Cutter and Combi Trimmer Router Bit suit users wanting flexibility from one cutter.

Frequently Asked Questions

What is a bearing guided trimming cutter used for?

It trims a workpiece flush with, or to a set angle from, an existing edge. The bearing follows the edge while the cutter removes the excess material.

Which Trend cutter suits laminate trimming?

The Double Trim cutter is well suited to laminate and veneered boards because it trims top and bottom in one pass. The bevel trimmer is better where an angled edge is needed.

Should I use the 16mm or 19mm bearing?

The 16mm bearing is supplied as standard. Fitting a 19mm bearing spreads wear across the cutting edges, so it can be worth using where you do a lot of trimming.

What is the difference between standard and CRAFTPRO trimmers?

Both cover similar trimming jobs. The CRAFTPRO series adds options such as 3 flute and double bearing designs, so check the specification against your material and finish requirements. Available from Tooled-Up.com.